Refurbishment: The Recycling of Your Wine Barrel Rack

BACKGROUND

When Topco Inc. began producing barrel racks for wineries in 1997, it was evident that these racks had a limited service life, primarily due to rust degradation. Although they were finished with high-quality powder coat, intrusions caused by denting or abrasion allowed metal exposure to the generally corrosive winery environment. Typically, after five to seven years of service, many racks are unfit for continued service. In addition, it was known that many wineries had extensive “bone yards” of damaged or obsolete racks which were rusting to perfection. Since then, Topco Inc. has searched for a solution. And now we are pleased to announce that one has been found.

THE RECYCLING PROGRAM

Although efficient stripping is the key to recycling wine barrel racks, an effective recycling program is important too. Topco Inc. offers four basic services: Refurbishment, Repair, Re-manufacturing and Removal.

1. Refurbishment

At customer’s order, racks to be refurbished are collected and delivered to us at our expense. Racks are then stripped, inspected, and categorized. Those found to be in serviceable condition, minor dings allowed, will be refinished with new powder coat in customer’s choice of color. Any racks that are not suitable for refurbishment become Topco Inc. property unless other arrangements are made. Return shipping costs are borne by the customer.

2. Repair

This service includes all the features and conditions of refurbishment, except that damaged racks will be repaired at a flat rate per rack to be determined on a case-by-case basis.

3. Remanufacturing

This service includes all the features of Refurbishment and Repair, except that racks will be modified at a flat rate per rack to be determined on a case-by-case basis. A common example of this type of service is the conversion of two crossbar racks to four crossbar racks.

4. Removal

Topco Inc. will be glad to remove and dispose of any unwanted racks at no cost to the customer.

SOLUTION

The key to recycling wine barrel racks depended on finding an effective, convenient, inexpensive and environmentally friendly way to remove rust and old finish material. And now a solution has been found. Topco Inc. is proud to announce the installation of a Pangborn Rotoblast wheel abrader system, which works like a sandblaster, only better. With the Rotoblast equipment, racks may be stripped to shiny bare metal in average of two minutes each or less. This machine is a self-contained factory. Inside a sealed cabinet, racks are stripped by two streams of high strength steel micro-balls, travelling at the rate of 700 lbs./min. by two large wheels at about half the speed of a 45 caliber bullet. The racks rotate on a turntable in front of these streams to expose as much surface as possible. Below the rotating table a material handling system recirculates the media from a trough in the bottom of the blast cabinet to a hopper above the slinger wheels. Finally, there is a sophisticated separation system that removes and captures all unwanted debris and dust. In all, this machine is about 22 ft. tall, 24 ft. wide, 15 ft. deep, and weighs about 61,000 lbs. not including the10,000 lbs. of media which it contains.

WINE RACK REFURBISHING

Topco Inc. is proud to announce our new Pangborn Rotoblast* system, which works like sandblasting, only better! With this equipment it is now possible to refurbish used racks by efficiently stripping them to shiny, slightly roughened clean metal, creating an excellent mechanical bonding surface for new powder coat.

Refurbishing your wine barrel rack not only saves the environment, it saves you money.

PANGBORN

IMG_3065

HOW THE PANGBORN WORKS

Our Pangborn* Rotoblast wheel abrader performs much the same task as sandblasting, except, in place of sand, super-hard steel microballs are hurled by a rapidly spinning paddle wheel at about half the speed of a 45 automatic bullet toward the material to be stripped. The entire process is self contained and fully automatic. Not only are the racks efficiently stripped, but surface roughened as well for superior powder coat adhesion.

THREE STEP PROCESS

redrusty1. Stripping: Each rack to be refurbished is stripped of rust and old paint, then inspected.

stripped2. Inspection: Racks in good physical condition are re-coated. Minor non- structural dings, usually caused by forklift handling, are allowed. A sophisticated ultrasonic device is used to spot check for wall thickness of the steel tube.

like new3. Refurbishment: Racks passing inspection are powder coated. The finished racks look like new.

Topco, Inc.

Print Friendly
Topco Logo Topco, Inc. Manufacture's new and refurbished barrel racks. We can also convert 2 barrel racks to 4 barrel. Seismic solution: TOPCAP. Contact 888.473.2005